TILTA WLC-T03 Nucleus-M Wireless Follow Focus Lens Control System TILTA WLC-T03 Nucleus-M Wireless Follow Focus Lens Control System Nucleus M Battery Included

TILTA - The signal from the fiz hand unit can be upgraded to 1 1/4 miles with an additional accessory. 08 mod, zoom, 32 pitch gear with a face width of 10mm. Connections between the FIZ hand unit and the two hand grips to the motors are completely wireless. Each motor has a built-in mdr unit, saving space and setup time.

Ideal for gimbal, Drone, and Shoulder-mounted setups. A single motor can be powered directly from the camera's battery though a 7-Pin to P-TAP cable then daisy chained via 7-Pin to 7-Pin cable to run additional motors. Motors can calibrate on lenses without hard stops - such as photo-lens with follow focus gears.

TILTA WLC-T03 Nucleus-M Wireless Follow Focus Lens Control System TILTA WLC-T03 Nucleus-M Wireless Follow Focus Lens Control System Nucleus M Battery Included - Motors fit standard 15mm and 19mm Rods. The batteries in the FIZ unit can last up to 10 hours. Fiz hand unit is capable of controlling 3 channels - focus, 35-tooth, and iris as well as overriding the hand grips. Specifications: weight: FIZ Hand Unit no batteries: 0972 lbs right handle Grip no batteries or adapters: 0

582 lbs left handle Grip no batteries or adapters: 0529 lbs arri rosette Male to Handle Grip Adapter: 0161 lbs gimbal to Hand Grip Adapter: 0

More information about TILTA

TILTA Nucleus-M Quick Release Handle Grip Bridge 15mm/15mm 19MM /15MM

TILTA NA - Simply fit the bridge onto the rods and use the hand-tightening screw to latch on. This hand grip bridge allows you to quickly connect your hand grips to your camera setup's rod system to allow you to be ready for handheld operation in seconds. Package include: 2* 90 degree arri standard rosette offset with tightening screws 1* tilta center tightening screw 1* 15/19 Tilta Quick Release Bridge Unit 2* 15mm Lightweight Rod Support Mounting Clips 2* 19mm Lightweight Rod Support Mounting Clips 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system.

More information about TILTA NA


Similar products:


Nucleus-M Run/Stop Cables, RED DSMC2

Tilta RS-02-RD - These cables for the Nucleus-M give you run/stop capabilities in camera systems that support it. Check other listings for lanc, sony f5/f55, 3-pin fischer, panasonic gh series, arri ext, red dsmc1, sony a6/a7/A9 series, and RED DSMC2 R/S connections. Control the record run/stop functionality of your camera by connecting the cable from the 7-pin port of one of the Nucleus-M motors to the camera's run/stop port.

. Simply plug the 7-pin end of the cable into one of the motors and the other end into the R/S port of the camera. Note that this cable was specifically designed for the Nucleus-M so the R/S function only works with the Nucleus-M’s own hand unit and handles. 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system.

Nucleus-M Run/Stop Cables, RED DSMC2 - Made specifically for the Tilta Nucleus-M Wireless Lens Control System.

More information about Tilta RS-02-RD


Similar products:


Alvin's Cables Nucleus M P-TAP to 7 Pin Motor Power Cable for Tilta

Alvin's Cables LW07MD - When powered through a p-tap connection, additional motors can be powered easily via daisy-chain using a 7-Pin to 7-Pin straight motor to motor connection cable. Designed to be lightweight and efficient, each brushless motor is made completely wireless via built-in MDR. A single motor can be also be powered by the G1's 14.

8v dc output - using the 3-pin to 7-pin power cable and the G1's DC to LEMO Distribution Box G1-DC-LE. The nucleus-M is a revolutionary follow focus system. Plug a: right angle 7 pin male connector. This 700mm p-tap to 7-pin power cable is used in the nucleus-m wireless follow Focus System to provide power to a single motor via the camera's battery or other P-Tap power supply source.

Alvin's Cables Nucleus M P-TAP to 7 Pin Motor Power Cable for Tilta - This 740mm p-tap to 7-pin cable easily powers a single Nucleus-M motor via P-TAP connection from either the camera's battery or other power source. Control the record run/stop functionality of your camera by connecting the cable from the 7-pin port of one of the Nucleus-M motors to the camera's run/stop port.

Power can then be re-distributed to other motors from the first motor via 7-Pin out. Cable length:07 meters we can customize. Plug b: P-dtap connector. 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system.

More information about Alvin's Cables LW07MD


Similar products:


SMALLRIG Base Plate Riser Plate for RED Raven/Scarlet-W/Epic-W/Weapon with Rod Clamp - 1756

SMALLRIG 1756 - Smallrig baseplate for Red Camera 1756 supports and stabilizes your camera well. You can mount quick release plate or 19mm bridge plate to make moving from shoulder mounting to tripod effortless. Power can then be re-distributed to other motors from the first motor via 7-Pin out. Cable length:07 meters we can customize.

Plug a: right angle 7 pin male connector. Also, mounting a lens support is a good choice. Plug b: P-dtap connector. Key features: 1. Fits well with your camera 2. Used with shoulder mounting or tripod 3. Anti-twist 4. 1/4" and 3/8" thread points around 5. 15mm rods and lens support attachment compatibility: for red raven for red scarlet-w for red weapon / for red weapon brain with helium 8k s35 sensor for red epic-w brain with helium 8k s35 sensor package includes: 1 x baseplate 1756 1 x 1/4" QR plate screw 1 x 3/8" QR plate screw 1 x rod clamp 2 x 1/4" screw 1 x hex spanner Product Dimensions: 111 x 83 x 31.

SMALLRIG Base Plate Riser Plate for RED Raven/Scarlet-W/Epic-W/Weapon with Rod Clamp - 1756 - 5mm net weight: 235g package size: 135x100x50mm package weight: 270g material: Aluminum Alloy 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system. Made specifically for the Tilta Nucleus-M Wireless Lens Control System. It allows to mount 15mm rods for follow focus and matte box attaching.

It is compatible with the 15mm and 19mm rods industrial standard.

More information about SMALLRIG 1756


Similar products:


1091 - SMALLRIG Cheese Bar with 1/4" and 3/8" Threaded Holes,Cheese Plate for Monitor Mount, DIY Camera Accessories

SMALLRIG SR-FM01-1091 - Multiple thread holes:camera cheese plate 1091 is equipped with industry standard 1/4"-20 and 3/8"-16 threaded holes, which make it possible to mount on any 1/4"-20 and 3/8"-16 accessories. You can also mount it onto Red camera or Red Rig because it comes with the RED screw spacing. Compatibility619ah, 819ah, fa1011 and FA1013.

Parametersnet weight: 58gmaterials: aluminum alloywhat you get1 x cheese bar2 x 1/4'' screw 2 x m4 screw1 x 1/4'' double head screw1 x hex screwHassle-Free WarrantyAt SMALLRIG, not only we offer high quality products, we back them up with 18-month warranty and a 30-day money back guaranty 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system.

1091 - SMALLRIG Cheese Bar with 1/4" and 3/8" Threaded Holes,Cheese Plate for Monitor Mount, DIY Camera Accessories - Made specifically for the Tilta Nucleus-M Wireless Lens Control System. Also, mounting a lens support is a good choice. Check other listings for lanc, arri ext, sony a6/a7/a9 series, 3-Pin Fischer, red dsmc1, panasonic gh series, Sony F5/F55, and RED DSMC2 R/S connections. Each cable was tested to ensure that there are no short circuit, no potential breakdown problems before shipping, and it works great!

It allows to mount 15mm rods for follow focus and matte box attaching. Smallrig baseplate for Red Camera 1756 supports and stabilizes your camera well. This 700mm p-tap to 7-pin power cable is used in the nucleus-m wireless follow Focus System to provide power to a single motor via the camera's battery or other P-Tap power supply source.

Multiple functions: it's handy for all those little conversion fit this camera mounting adapter, it can be used as an on-camera multi-gadget mounting accessories, or simply use it as an additional handle when fitted to the top of a camera.

More information about SMALLRIG SR-FM01-1091


Similar products:


BongoTies Original Bongo Ties A5-01 ~ 10 Pack ~ Handy Ties for Cables and Other Unruly Items

Bongo Ties A5-01 - Multiple thread holes:camera cheese plate 1091 is equipped with industry standard 1/4"-20 and 3/8"-16 threaded holes, which make it possible to mount on any 1/4"-20 and 3/8"-16 accessories. All-natural - made entirely of renewable organic materials, bamboo and natural Hevea rubber. It allows to mount 15mm rods for follow focus and matte box attaching.

Also, mounting a lens support is a good choice. Use it to interconnect various camera accessories and set up extra parts as needed. Smallrig baseplate for Red Camera 1756 supports and stabilizes your camera well. For diy camera accessories : useful and versatile little bar for DIY camera mount. Power can then be re-distributed to other motors from the first motor via 7-Pin out.

BongoTies Original Bongo Ties A5-01 ~ 10 Pack ~ Handy Ties for Cables and Other Unruly Items - Cable length:07 meters we can customize. Multiple functions: it's handy for all those little conversion fit this camera mounting adapter, it can be used as an on-camera multi-gadget mounting accessories, or simply use it as an additional handle when fitted to the top of a camera. You can mount quick release plate or 19mm bridge plate to make moving from shoulder mounting to tripod effortless.

It is compatible with the 15mm and 19mm rods industrial standard. Plug b: P-dtap connector.

More information about Bongo Ties A5-01


Similar products:


Alvin's Cables Lanparte LP E6 Dummy Battery to D-Tap Cable for SmallHD 501 502 702 Monitor and Canon 5D4 5DSR 5D2 5D3 6D 60D 7D 7D2 70D 80D

Alvin's Cables E6TDT2 - Hope our products can satisfy your demand. Moreover, it is allowed to customize the cables according to your requirements. You can mount quick release plate or 19mm bridge plate to make moving from shoulder mounting to tripod effortless. Please note, not lp e6 real lithium battery, we could call it dr e6 dummy battery too, it can't be used for Blackmagic camera, the appearance is different from the LP E6 real lithium battery, but it will work for the device we mentioned above About the detail, please don't use it for the others that we do not mention.

Use it to interconnect various camera accessories and set up extra parts as needed. Please ensure that the output of the power source does not exceed 16. 8v. The output is about 8V. No plastic ~ no nylon. Control the record run/stop functionality of your camera by connecting the cable from the 7-pin port of one of the Nucleus-M motors to the camera's run/stop port.

Alvin's Cables Lanparte LP E6 Dummy Battery to D-Tap Cable for SmallHD 501 502 702 Monitor and Canon 5D4 5DSR 5D2 5D3 6D 60D 7D 7D2 70D 80D - . If you are interested in them, please contact us, thank you! 15mm/19mm bridge allows you to quickly connect your Nucleus-M Handle grips to either a 15mm rail system or 19mm rail system. Made specifically for the Tilta Nucleus-M Wireless Lens Control System. Smallrig baseplate for Red Camera 1756 supports and stabilizes your camera well.

More information about Alvin's Cables E6TDT2


Similar products: